Fundamental Plumbing Tips for Bathtub Installation
Fundamental Plumbing Tips for Bathtub Installation
Blog Article
On this page in the next paragraph you will discover a good deal of reliable answers with regards to How to Install a Bathtub.
Installing a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult job. If the old bathtub is readily accessible, the job can relocate easily; if you need to open up a wall to remove the old tub and also place the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you install a brand-new bathtub in your bathroom if you have actually currently gotten a new tub as well as do not need to transform the setup of your previous supply of water pipes.
Your tools and product checklist must make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Safeguard the faucet in place with the producer offered backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The former type should be connected to the tap finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub up until the level checks out degree.
To install taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints as well as new pipework for leaks and also tighten them if necessary. Load the bath tub as well as also check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bathtub should wait till the bathtub has actually been utilized at least when as this will certainly settle it right into its final position.
Planning for the Installation
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, triggering the water to penetrate the wall between the bath and the tiling, resulting in problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the market. It is a good idea to fit the tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our post about How to Install a Bathtub Yourself. Thanks a lot for taking a few minutes to read through our piece. Do you know somebody who is looking into the topic? Please feel free to promote it. Thanks for your time. Visit again soon.
Book Inspection Report this page